# Time 2 Bumper Opinions?

**URL:** <https://forum.repebble.com/t/time-2-bumper-opinions/1923>\
**Category:** General Discussion\
**Created:** [November 2, 2026, 9:10am UTC](https://forum.repebble.com/t/time-2-bumper-opinions/1923 "2026-11-02T09:10:38Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![tudza](https://yyz1.discourse-cdn.com/flex033/user_avatar/forum.repebble.com/tudza/32/431_2.png) [@tudza](https://forum.repebble.com/u/tudza)\
**Post date:** [November 2, 2026, 9:10am UTC](https://forum.repebble.com/t/time-2-bumper-opinions/1923/1 "2026-11-02T09:10:38Z")

</div>

I got some Gadgeteer screen protectors and installed one.

Wondering if I should get one of the bumpers people mention once and while?

Suggested sources? ( I can have someone 3D print if that’s the best way to go. )

---

<div class="post-metadata">

**Author:** ![Flynn](https://yyz1.discourse-cdn.com/flex033/user_avatar/forum.repebble.com/flynn/32/73_2.png) [@Flynn](https://forum.repebble.com/u/Flynn)\
**Post date:** [November 2, 2026, 3:31pm UTC](https://forum.repebble.com/t/time-2-bumper-opinions/1923/2 "2026-11-02T15:31:35Z")

</div>

There’s [Bumper | Pebble Time 2 case cover - Favourite Human Design by astosia](https://favouritehumandesign.com/product/bumper-pebble-time-2-case-cover-2/)

And [https://thangs.com/designer/astosia%20/3d-model/Bumper%20|%20Pebble%20Time%202%20Case-1554295](https://thangs.com/designer/astosia%20/3d-model/Bumper%20%7C%20Pebble%20Time%202%20Case-1554295) for printing it yourself

---

<div class="post-metadata">

**Author:** ![tudza](https://yyz1.discourse-cdn.com/flex033/user_avatar/forum.repebble.com/tudza/32/431_2.png) [@tudza](https://forum.repebble.com/u/tudza)\
**Post date:** [November 2, 2026, 3:48pm UTC](https://forum.repebble.com/t/time-2-bumper-opinions/1923/3 "2026-11-02T15:48:50Z")

</div>

Thanks. I’d run across those while looking around. I also see there is a variation on the charging stand I’ve already downloaded a .stl file for that I hadn’t seen yet.

---

<div class="post-metadata">

**Author:** ![ChicoryCafe](https://avatars.discourse-cdn.com/v4/letter/c/f14d63/32.png) [@ChicoryCafe](https://forum.repebble.com/u/ChicoryCafe)\
**Post date:** [November 4, 2026, 7:41am UTC](https://forum.repebble.com/t/time-2-bumper-opinions/1923/4 "2026-11-04T07:41:24Z")

</div>

I like [this model](https://www.printables.com/model/1713882-simple-bumper-case-for-pebble-time-2) from Jake of All Trades on Printables, though it can pop off if pressed from the bottom a bit (though most bumpers will as far as I can tell)

Requires 3D printing, but uses essentially no filament, so you could have someone print like 20 of them overnight and you’d probably never run out.

PLA or PETG works fine, no major difference in how well it stays on in my experience.